TradeExamPro

Asbestos, Mold and Radon Professional Practice Test

Practice questions on asbestos rules and abatement, mold assessment and remediation principles, and radon measurement and mitigation, based on public federal rules and EPA guidance.

211 questions · 6 topics · start free, no sign-up

Start practising

Mixed practice test

10 questions, graded as you go, with the reason for every answer. Start free, no sign-up.

Timed mock exam

50 questions in 60 minutes, drawn from every topic. No answers shown until the end, then a score, your weakest topics and a review of what you missed.

Practise by topic

Sample questions

A single homogeneous area of friable sprayed-on ceiling surfacing covers 3,500 square feet. At minimum, how many bulk samples does the AHERA inspection rule call for?

  1. 3
  2. 7
  3. 9
  4. 5
Show the answer

D. 5

For surfacing material, 1,000 sq ft or less needs 3 samples, more than 1,000 up to 5,000 sq ft needs 5, and more than 5,000 sq ft needs 7. At 3,500 sq ft the middle tier applies, so 3 is too few.

Reference: 40 CFR 763.86

A crew will remove asbestos-containing vinyl floor tile. Which OSHA class of work is this?

  1. Class I
  2. Class II
  3. Class III
  4. Class IV
Show the answer

B. Class II

Removing ACM that is not thermal insulation or surfacing material, such as floor tile, sheeting, roofing or siding, is Class II. Class I is limited to thermal system insulation and surfacing material.

Reference: OSHA 29 CFR 1926.1101(b), definition of Class II work

Dust in an area is measured at 30 times its exposure limit. Which respirator is the lowest-protection choice that still has an adequate APF?

  1. Half-mask air-purifying respirator (APF 10)
  2. Full facepiece air-purifying respirator (APF 50)
  3. Loose-fitting hood powered air-purifying respirator (APF 25)
  4. Quarter-mask air-purifying respirator (APF 5)
Show the answer

B. Full facepiece air-purifying respirator (APF 50)

The APF must be at least the hazard ratio, here 30. The full facepiece respirator at 50 qualifies. The hood at 25 looks close but falls short, and the half-mask and quarter-mask are far below 30.

Reference: OSHA 29 CFR 1910.134(d)(3)(i)(A), Table 1

A homeowner finds visible mold on a bathroom wall. What does EPA guidance say about sampling here?

  1. Usually unneeded; clean visible mold
  2. It is always required before any cleaning starts
  3. It is required to prove the mold type to the city
  4. It must be done by the homeowner with a home kit
Show the answer

A. Usually unneeded; clean visible mold

When mold is visible, sampling is usually not needed because the response is the same: fix the moisture and remove the growth. Sampling answers special questions; it is not a routine first step.

Reference: EPA, Mold Remediation in Schools and Commercial Buildings (EPA 402-K-01-001), Chapter 3 (sampling)

For how long before a short-term radon test starts must closed-building conditions be kept?

  1. About 1 hour
  2. At least 12 hours
  3. About 3 days
  4. Only after the device is placed
Show the answer

B. At least 12 hours

Closed-building conditions mean keeping windows and outside doors shut except for normal entry and exit, starting at least 12 hours before the test and continuing through it. Starting late lets outdoor air dilute the indoor level.

Reference: EPA, Home Buyer's and Seller's Guide to Radon

Exams this helps with

ExamWho runs itWhere
Asbestos worker / supervisor / inspectorEPA (AHERA), statesUnited States (varies by state)
Mold assessor / remediatorState boardsUnited States (varies by state)
Radon measurement and mitigationNRPP, NRSBUnited States